The model number on our old ice maker unit was S I admit that I had a little trouble cross-referencing this exact number, it did not show up on any replacement list I could find. That said, I was able to go directly to the Supco web site where they gave a lot more information about these ice makers - which I knew nothing about before I started.
I guess I had no idea that ice makers like this were such a drop-in commodity.
How to Hook up the Ice Maker & Water System on a Kenmore Refrigerator
The RIM model from Supco was a nearly identical replacement for my ice maker. I ended up having to re-use the wiring Whirlpool Ice Maker Assembly. Exactly as advertised, bolted right up without problem. As other users have mentioned it requires you to swap the metal bar and the cover panel from the old unit.
In my case I also found that the small wiring harness that comes with the replacement unit wasn't needed for my particular model of refrigerator. My wiring harness comes straight through the wall of the freezer to the icemaker rather that requiring the pigtail that came with the unit.
Easy swap and no my icebox has ice cubes in it and not just one big block of ice. Whirlpool Complete 8 Cube Icemaker Assembly.
And once we learned how to pull it out thank you, youtube , we found the plastic on the ice cube holder itself was de-laminating. The little ice robot is happy and the container in the door is properly filled. Replacement ice maker works better than the one that came on the refrigerator!! Only 1 left in stock - order soon.
Turn the water fill tube above the icemaker so that it fits inside the icemaker fill cup. Wrap plumber's resin-coated tape around the nozzle threads on the back of the refrigerator, on the freezer side near the top.
Push the tape into the threading on all sides. Slide the coupler on the end of the water line over the taped nozzle on the back of the Kenmore.
Kenmore Refrigerator Ice Maker: stisgetehuchi.ml
Twist the coupler clockwise with your fingers as far as it will turn, then twist a half turn with pliers to seal the connection. Turn the water supply valve knob counterclockwise to release water to the Kenmore.
- reality dating shows australia.
- How to Hook Up a Kenmore Icemaker?
- available 123 dating!
- How to Hook Up a Water Line to a Refrigerator From the Sink | Home Guides | SF Gate.
Check the back of the refrigerator for any leaks around the connection. Tighten the coupler with pliers, if necessary. Dry your hands before plugging in the Kenmore power cord to the wall outlet.
Top Selected Products and Reviews
Press the toggle switch on the icemaker to the ''On" position and replace any frozen food you removed earlier. References Manage My Life: Turn on the cold water faucet to drain any water left in the supply line. Use pliers to untwist the faucet supply line from the cold water supply valve.
Wrap threads on the cold water valve with two or three wraps of thread-seal tape. Twist the male end of a quick-tee adapter onto the valve. Wrap the female thread on the opposite end of the adapter with thread-seal tape.
- Kenmore Refrigerator Ice Maker.
- How to Hook Up a Kenmore Icemaker | HomeSteady.
Twist the faucet supply line onto the female end of the adapter. Slip the compression nut that came with the kit over the newly installed supply line. Make sure the threads are facing the end of the line. Thread the ferrule from the kit onto the new line. Wrap the remaining male threads on the quick-tee adapter with thread-seal tape. Insert the new water line into the opening on the tee. Slide the compression nut over the male threads and tighten it on the adapter.click
How to Hook Up a Water Line to a Refrigerator From the Sink
Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. Place the end of the water line you intend to connect to the refrigerator into a 5-gallon bucket. Turn the cold water supply valve on beneath the sink.